How to Install Sump Pump in a Crawl Space

How to Install Sump Pump In a Crawl Space: Professionals Do This

Is it true that there is no better way to prevent a crawl space flood than with a sump pump? When you install a sump pump in your crawl room, it protects your house from molds or rot. This is due to water damage. This pump utilizes a submersible float rising and falling with the groundwater table. 

When floods influence the surge, a regulator turns on and it begins to remove the water. Thus draining it through the outlet to the exterior. Its installation demands a lot of time even though it is better to protect your house from unpleasant destruction. So, what makes your crawl space damp? The reasons are;

  • Lack of proper drainage system.
  • leakages due to plumbing.
  • more humid temperatures.
  • lack of dampness barrier between a crawl space and dirt.
  • Higher groundwater level than the floor of your house.

There are 7 steps on  how to install sump pump in a crawl space;

How to Install Sump Pump Drain System

1.    Identifying The Best Spot for The Sump Pump Basin – Crawl Space Sump Pump Basin

How do you find a precise location for the crawl space sump pump basin? The position has to be centered and close to the opening. Hence you can clog in the sump pump. You can also assess the area the pump will be carrying the water outside. 

You can also check on the area to dig the hole that will carry the water pipe. Note that when identifying the basin, then check on a proper drainage system and the nearness to an available power source.

2.    Dig a Pit for The Sump Pump

In case you feel like digging out yourself, you may consider consulting an expert. This so that you do not interfere with the foundation of your house. Dig a deep hole that can set up the pump basin in it. Then replete with the floor.

3.    Preparing The Basin For Installation

Drill some drainage voids for the sump pump before you lower it in the hole. And before you discharge the pump in the basin, you can line the base with sand and then set the seepage conduit. If everything is done, replenish the rest of the conduit around the basin with gravel about two inches from the top of the basin.

4.    Install The Pump

Do you understand how to install sump pump drainage system? Take the pump and place it in the basin. Ensure you attach the plumbing that you require. Put in a weep hole in the PVC duct for easier water transport. Consider drilling a weep hole that is six inches from the pump connection.

5.    Attaching the Pump

How can you ensure the pump is connected as required? You can cover and connect the pump. Take its cover and position it appropriately. Also, you can consider making a connection of the sump pump to the release line. You can then proceed to connect the power supply to the system and then ventilating the plumbing.

6.    Finalize The Process – Crawl Space Sump Pump Discharge

How will the crawl space sump pump discharge water? First, you can set up the crawl room. To finish up the crawl area, crowd the location with sand in the position of your pump and go on with installing the remaining drainage tube. Also, you can drill a hole in the wall where the drainage will move through. Next, proceed to do the installation. Run the pipe at least four inches from your house and then set up a water discharge system.

7.    Do The Power Connection

The last part of the installation is to connect a steady power supply. Without this, there is no way water will be pumped out. The structure has to run and therefore plugin the cable into the power supply. After the connection, you can confirm if the pump is working as required or not. This process will help you see any defect in your pump and then do the repair.

Why Should You Consider Learning How to Install Sump Pump in a Crawl Space?

The 2 Reasons You Can Consider Installing a Sump Pump are;

  • The water from the groundwater table can destroy your house. If you are staying in the regions that are prone to the long continuous rains, you can end up with water under the house. Your crawl space may be wet all through. In the case of no or little rains, the crawl space can still be damp. 

During the rains, the water will cause the moist areas of the crawl space to enlarge. Hence wet the whole room. If there are no rains and the room is still wet, then you can check the water supply or drainage pipes around. There may be some leakages.

  • The water in the crawl space may be annoying. You may think of the water as disturbing and has an awful element in your house. This is more than a little problem. This can lead to health issues or even structural threats. 

Much water with no or less light ends up producing mold in your house. These two conditions favor the growth of mold. The molds can grow on the surface of the crawl room, the piers, and the joists.

Final Thoughts

It is vital to learn how to install sump pump in a crawl space. Just because you don’t experience any issues with your basement, does not mean you don’t install the sump pumps. The use of sump pumps in the crawl space is one widespread solution you can use to keep your crawl room dry. The pumps are installed in the crawl room because it is the area where water collects more frequently. The pumps are run on a power supply and you can therefore install them close to electricity. If electricity is a problem, you can go for a pump that runs on batteries. This is important because there are times when flooding can affect the electrical system. You can consider putting in two pumps if you have enough capital to do so. Having two pumps, with one as the major and the other as the backup. This will help you prepare for emergencies.

Scroll to Top